In order to view this object you need Flash Player 9+ support!

Get Adobe Flash player

Thermo Insulation Products

AA-100 Packing Extraction Hooks
These tools are designed to assist in the removal of packing rings from the stuffing box. They are ideal for packing that has become hard, burned or flaky. These hooks work well where standard screw packing extractors tend to only want to pull out small pieces of packing.

 

 

AA-200 Packing Tamping Tools
For the best results when packing a stuffing box, each packing ring should be tamped firmly into place to insure a seal to the shaft and the walls of the stuffing box. These tools are designed to help you accomplish this. The Tamping Tools are made from flexible high strength material.


 

AA-300 Hose cutter
Largest cutter - cuts hose through 2" I.D., P.E. through 1-1/2" & Class PVC through 1-1/4" I.D. (Comes standard with Stainless Steel Blade)

   


 

 

AA-400 Gland Packing Extractors

The Packing Extractor is designed to facilitate the removal of old packing of any size from 3/16” upward. This can be a difficult and tiresome procedure made simple and quick by the use of the Packing Extractor. The long flexible shank of the Packing Extractor makes access easy even to those glands in the most awkward positions. The hardened and tempered steel screw end is designed to give maximum penetration into packing. Flexible Packing Extractors are supplied individually or in boxed kits of all four sizes. The Packing Extractors with the renewable tips come complete with two new tips. Individual spare tips may be purchased as required.


Stock Code
Description Packing Sizes Total Length
0001 0001-Size1 Renewable 3/16”-1/4” 7-1/2”
0002 0002-Size2 Renewable 5/16”-3/8” 11”
0003 0003-Size3 Renewable 7/16”-5/8” 14”
0010 0010-Kit Full Set 0001,0002 & 0003 - -
R 0001 Size 1 Replacement Tip - -
R 0002 Size 2 Replacement Tip - -
R 0003 Size 3 Replacement Tip - -

 

AA 500- Super Slide Injection Gun
The injection gun utilizes a button-head or flow-through fitting permanently  installed on the pump or valve stuffing box. Since it requires no electricity, the injection gun can be used anywhere to replenish sealant easily and conveniently. The all-steel hydraulic gun is completely portable and is very easy to use. The valve or pump stuffing box fitting allows the sealant to be hand-injected into the shaft stuffing box using the injector gun. No downtime is required for the repacking operation since the equipment can continue to run during the repacking operation. The BJSEAL AA-500 Hydraulic Hand Gun features a unique locking handle to prevent pump piston damage. Hydraulic pressure is generated by stroking the handle. The cleaner or lubricant / sealant is discharged at up to 10,000 psi. Discharges 1 oz. of product easily with each 50 strokes.

• Generates up to 10,000 psi when required.
• Light weight, very portable.
• Can also pump liquids, flange sealants and stem packing’s.
• Self-priming hydraulic action makes manual injection simple.
• Reloads easily with a 12 oz. cartridge from BJSEAL
• Pumps gun-packs and all types of sealants.

 

AA 600 Packing Cutter
BJSEAL AA 600 Packing Cutter will save time, money and braided packing while providing precision skive and butt cuts for the highest quality packing  installations. Bjseal Cut Packing Cutter will cut a number of different packing’s. Perfect 45 degree (Skive) or 90 degree (Butt) cuts are accomplished by  changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence   line up with alignment holes in table. Perfect 45 degree (Skive) or 90 degree (Butt) cuts are accomplished by changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence line up with alignment holes in table.

The Packing cutter cuts Teflon, Cotton yarn, GFO yarn, Acrylic Rayon Fiberglass yarn, Lead Foil packing, Inconel wire carbon yarn packing; will cut some Kevlar/composite packing; not designed to cut pure Kevlar. Packing cutter has also been used to cut large o-ring material, Felt & rubber seal strip materials.


AA-625 Gland Packing Cutter

 
BJ6 AA625 Packing Cutter will save time, money and braided packing while providing precision skive and butt cuts for the highest quality packing installations. AA 625 Cut Packing Cutter will cut a number of different packing’s. Perfect 45 degree cuts are accomplished by changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence line up with alignment holes in table. Perfect 45 degree (Skive) cuts are accomplished by changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence line up with alignment holes in table,robust and accurate cutting jig that simplifies the production of perfectly matching 45° scarf joints on packing.

The Packing cutter cuts Teflon, Cotton yarn, GFO yarn, Acrylic Rayon Fiberglass yarn, Lead Foil packing, Inconel wire carbon yarn packing; will cut some Kevlar/composite packing; not designed to cut pure Kevlar. Packing cutter has also been used to cut large o-ring material, Felt & rubber seal strip materials.Packing Cutter PC10 SIZE Packing Ring Cutter - 10"(1" max. packing size - 10" max. shaft size).Just match the section of the packing to the ring inside diameter required, then simply cut the exact ring length required with perfect scarf joints.

AA 650 Water Jetting Packing Extractor-Air Operated

The model AA 650 water, jet packing extraction, system consists of an air operated, high pressure pumping system, high pressure hose, extraction gun, portable reservoir, and nozzle kit. This system has been designed for fast and efficient removal of valve stem packing, pump packing and flange gasketing. It also eliminates the risk of scoring or gouging a valve stem, stuffing box bore, or flange face cause by out-dated manual extraction methods. The AA 600 system allows for instantaneous flow control at the gun without the use of any electrical or pneumatic remote controls or switches. The Extraction gun is a hand held device that is activated by depressing a gun type trigger. This allows for a safe and positive flow shut-off control at the gun. Releasing the gun trigger stops all jetting flow instantaneously, regardless of the distance from the pumping unit. When the trigger is released, the pump unit will stall at the preset operating pressure. The AA 650 provides the operator with the ultimate in safety and positive control of the amount of water or chemical used in the extraction process.

Features
      • All controls located on control panel, behind lockable ventilated door.
      • Discharge pressure to 20,000 PSIG-(138MPa)(1400BAR)
      • No electrical components for safe, non sparking operation.
      • Operates using plant water via hose or non pressurized portable reservoir.
      • Stainless steel console, corrosion resistant, with rear panel removal, drawer like entry with           no piping  to disconnect.
      • Sample case size, light weight, for operating in tight spaces and elevated areas.
      • Reduce labor cost/1man operation
      • Plant air operated system
      • High pressure relief valve
      • Water inlet filter, auto drain air filter.


Specifications
     • Size: 11"High x 20" wide x 17" deep (28cm x 51cm x 43cm)
     • Weight: 87 pounds(40kg)
     • Air Requirements: 70 to 100psi @ 50cfm
     • Gun: 20,000 PSI-WP
     • Hose: 26,000 PSI-WP, 60,000 PSI
     • Burst, 1\2" O.P.

 

AA-700 Extension Gasket Cutter Kits
Now you can accurately cut your own gaskets quickly and efficiently to reduce costly downtime. AA700 Extension Gasket Cutters are available in five convenient sizes to meet a broad range of cutting requirements. All kits come packed in a durable metal storage box for protection and convenience. Each kit contains all that is needed to cut your required gaskets quickly and accurately to size. Each Kit Contains: Cutter block, cutter head screws, regular gasket cutter blades, heavy duty cutter blades, pivot post, knurled nuts, centre pins, extension bars, suitable cutting board, piercing tool and necessary ancillary tools.

Extension gasket cutter kits - Inch

Item no

Gasket Sizes

BJ-AA700-100K13-Kit No 1 Gasket Cutter Kit Complete Cuts ¼” to 13”

BJ- AA700-100K25-Kit No 2

Gasket Cutter Kit Complete Cuts ¼” to 25”
BJ- AA700-100K37-Kit No 3 Gasket Cutter Kit Complete Cuts ¼” to 37”

BJ- AA700-100K49-Kit No 4
Gasket Cutter Kit Complete Cuts ¼” to 49”

BJ- AA700-100K61-Kit No 5
Gasket Cutter Kit Complete Cuts ¼” to 61”

BJ- AA700-100U13-Kit no 6
Gasket Cutter Kit w/o Cutting Board Cuts 1/4" to 13"

 

Extension gasket cutter kits - Metric

Item no

Gasket Sizes

BJ- AA700-100KM330-Kit No-1 Gasket Cutter Kit Complete Cuts 6mm to 330mm

BJ- AA700-100KM635-Kit No-2

Gasket Cutter Kit Complete Cuts 6mm to 635mm
BJ- AA700-100KM940-Kit No-3 Gasket Cutter Kit Complete Cuts 6mm to 940mm
BJ- AA700-100KM1245-Kit No-4 Gasket Cutter Kit Complete Cuts 6mm to 1245mm
BJ- AA700-100KM1550-Kit No-5 Gasket Cutter Kit Complete Cuts 6mm to 1550mm
BJ- AA700-100UM330-Kit No-6 Gasket Cutter Kit w/o Cutting Board 6mm to 330mm


AA 800 Hollow Punch Tools
AA800 Hollow punch is unique patented locking system allows for quick and easy interchange of cutting heads. Dual cutting heads allow for cutting inner and outer dimensions at the same time. Cutting heads may also be used individually for precision cuts as shown on the right. Cut a multitude of different materials including foam, cardboard, leather, rubber, fiber, plastic, gasket material and lead.


 

Hole punch kits-Inch

Item no Punch sizes

AA800-AH100K11-Kit-1
10 PUNCH SIZES: 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"
AA800-AH100K16-Kit-2 15 PUNCH SIZES: 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8, 1", 1 - 1/16", 1 - 1/8", 1 - 3/16"
AA800-AH100K27-Kit-3 25 PUNCH SIZES: 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8, 1", 1 - 1/16", 1 - 1/8", 1 - 3/16", 1 - 1/4, 1 - 5/16, 1 - 3/8", 1 - 7/16", 1 - 1/2", 1 - 5/8", 1 - 11/16", 1 - 3/4", 1 - 7/8", 2"

Hole punch kits-Inch

Item no Punch sizes
AA800-AH100KM11-Kit-1 11 Piece Hollow Punch Tool Kit- 10 PUNCH- SIZES: 3mm, 4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm
AA800-AH100KM16 Kit-2 16 Piece Hollow Punch Tool Kit- 15 PUNCH-SIZES: 3mm, 4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm, 26mm, 28mm, 30mm
AA900-AH100KM31 Kit-3 31 Piece Hollow Punch Tool Kit 29 PUNCH -SIZES: 2mm, 3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm, 26mm, 28mm, 30mm, 32mm, 34mm, 36mm, 38mm, 40mm, 42mm, 44mm, 46mm, 48mm, 50mm













AA 900-PTFE-Flexible Lantern Ring Material
BJSEAL AA900 Made of 100% PTFE material, Flexible Lantern Material is an innovative approach to standard lantern rings. Designed to perform like lantern rings, Flexible Lantern Material is easier to install and remove. Sold in roll form like bulk packing, Flexible Lantern Ring Material can be cut to the specific length needed, therefore eliminating the need to stock many different size rings. The Lantern Ring is simple to use. Just uncoil the length, wrap it around the pump shaft and butt cut to size. Ring will spring to the bore of the stuffing box, providing shaft clearance. For perfect end joint fit, wrap two turns of electrical tape around a mandrel of the same size as pump shaft and butt cut. Size Selection: Choose the same size as the packing cross section and choose the width which match
Standard Sizes

- All sizes in 4 FT. (1.22 MTR) lengths

Cross Section Width Length
1/4" 3/8" 1.2
5/16" 7/16" 1.2
7/16" 9/16" 1.2
1/2" 5/8" 1.2
9/16" 11/16" 1.2
5/8" 3/4" 1.2
3/4" 7/8" 1.2
7/8" 1" 1.2
1" 1" 1.2
Contact Info
world map

BJSEAL ENGINEERING PVT. LTD.


BR1-350, JAI GANESH VISION
AKURDI, PUNE - 411035
MAHARASHTRA, INDIA.


Phone :+91-20-27483060

Fax :+91-20-27487080


Email :
sales@bjseal.com
 
Quality
 We are maintains ongoing quality assurance checks throughout the manufacturing process.
Read More....

News
BJSEAL is at the forefront of the engineering business and regularly produces press releases we offer to our customers.
Read More....